On November 19, 2026, we read the Keystone product pages and cleaning procedures guide, the Safety Data Sheet Keystone points to for its Fryer & Grill Cleaner, the Break-Up Professional spec sheet and its NSF registration letter. We checked our own live product pages for pack sizes. Then we went through Google People Also Ask, autocomplete, Reddit kitchen threads, Quora and X to see what cooks actually ask. Most top results give generic steps without a dose, so we lead with the label numbers.
How to Boil Out a Commercial Fryer With Keystone Fryer Cleaner
How to Boil Out a Commercial Fryer With Keystone Fryer Cleaner
Doses, temperatures, contact times and safety notes for Keystone Fryer Cleaner, Break-Up Professional and Keystone Fryer & Grill Cleaner, with a planner for your fryer line.
Drain the oil, fill the fryer with cold water to cover the elements, add one 8 oz Keystone Fryer Cleaner packet for a 50 lb fryer and hold it at 180°F to 210°F for 15 to 20 minutes. Scrub, drain and rinse with hot water at least three times. The formula is non-caustic, so it needs no vinegar or acid rinse.
Key Takeaways
One packet per 50 lb fryer
Keystone sizes its 8 oz packet for a 50 lb fryer. A case holds 26 packets.
Hot, not a rolling boil
Hold 180°F to 210°F on the boil-out setting. A rapid boil can push solution over the top.
Dry before you refill
Water left in the pot breaks down fresh oil and spatters when the fryer heats up.
Check the metal
Keystone Fryer Cleaner and Break-Up are safe for aluminum. Keystone Fryer & Grill Cleaner isn't.
How we put this guide together
What is a fryer boil-out?
A boil-out cleans the inside of a fryer by heating water and a fryer cleaner in the frypot. Heat and chemistry loosen the carbon and gummy, polymerized oil that builds up on the walls and elements. Keystone's guide says to clean the fryer when you change the oil, and the job takes about 45 minutes.
Boil-out products are a specific class. Break-Up Professional is NSF registered in category A8, a degreaser or carbon remover for cooking equipment, with a potable water rinse required after use. That's the line between a boil-out and a general cleaner. For hoods and flat tops, see our oven cleaner vs degreaser guide.
How many Keystone Fryer Cleaner packets does a fryer need?
Keystone says one 8 oz packet for a 50 lb fryer. Break-Up Professional uses one 2 oz pouch for a 15 to 20 lb fryer and two for a 30 to 40 lb fryer. Keystone Fryer & Grill Cleaner is a liquid, dosed at 1 to 2 quarts per fryer. Always fill with water first, then add the cleaner.
Packets make dosing hard to get wrong. Nobody guesses how much to pour, and you can count a case against your boil-out schedule. Keystone Fryer Cleaner comes 26 packets to the case and Break-Up Professional comes 36 pouches to the case. The planner below turns your fryer count into cases per month.
What temperature and how long do you boil out a fryer?
For Keystone Fryer Cleaner, use the boil-out setting and hold 180°F to 210°F for 15 to 20 minutes. Avoid a rapid boil, because it can spill solution out of the fryer. Break-Up calls for a gentle boil for 10 to 30 minutes at about 225°F (105°C). Keystone Fryer & Grill says boil 15 minutes or soak 1 to 3 hours.
Those numbers come straight from each manufacturer, and they don't match, so follow the product you're using. While Break-Up is boiling, its directions say to brush or scrape soil above the oil line. With Keystone, turn the fryer off and let it cool before you scrub.
Do you need a vinegar rinse after a boil-out?
Not with these products. Keystone says its Fryer Cleaner needs no acidic rinse, and Break-Up says no neutralizing step is required. Rinse with hot water at least three times, at 110°F or hotter per Keystone's guide. Then dry the pot fully with clean paper towels or let it air dry before adding oil.
Vinegar rinses come from older caustic boil-outs, and some kitchens still do them by habit. A cook on Reddit r/KitchenConfidential asked about exactly that. Water left in the pot is the real risk. Keystone warns it breaks down fresh oil and spatters when the fryer heats. Good oil care starts here, as our fries reheating guide explains.
What safety gear and SDS warnings apply to fryer cleaners?
Keystone's guide says to wear protective gloves, an apron and goggles for fryer cleaning. The Safety Data Sheet for Keystone Fryer & Grill Cleaner lists 5 to 10% sodium hydroxide and the signal word Danger. It causes severe skin burns and eye damage, so store it locked up and away from acids.
Keystone Fryer Cleaner is non-caustic, which is easier on people and on aluminum. Break-Up is the opposite end of the scale, with a pH of 1.9. Never mix boil-out products or follow one with another in the same water. Our guide to cleaning chemicals you should never mix explains why. Keep the SDS binder next to the chemical shelf.
Fryer boil-out planner: dose, cases and settings
Pick the boil-out product, your fryer size, how many fryers you run and how often you boil out. The planner shows the dose per fryer, packets or litres per month, cases per month and the label heat, time and rinse steps.
1 packet per boil-out
| Plan | Value |
|---|---|
| Dose | 1 packet |
Doses, temperatures and times come from the manufacturer directions. Keystone Fryer Cleaner: 1 packet for a 50 lb fryer, 180°F to 210°F for 15 to 20 minutes, 26 packets per case. Break-Up Professional: 1 pouch for a 15 to 20 lb fryer, 2 for 30 to 40 lb, gentle boil for 10 to 30 minutes at about 225°F, 36 pouches per case. The 50 lb Break-Up figure uses its 1:170 dilution. Keystone Fryer & Grill Cleaner: 1 to 2 quarts per boil-out, boil 15 minutes or soak 1 to 3 hours, two 3.78 L jugs per case. A month is 4.33 weeks.
Keystone vs Break-Up vs Fryer & Grill Cleaner
| Product | Item ID | Pack | Dose | Heat and time | Aluminum |
|---|---|---|---|---|---|
| Keystone Fryer Cleaner | 6018113311337 | 26 x 8 oz packets | 1 packet per 50 lb fryer | 180°F to 210°F, 15 to 20 min | Safe |
| Break-Up Professional | 7425145444466 | 36 x 2 oz pouches | 1 pouch per 15 to 20 lb, 2 per 30 to 40 lb | Gentle boil, about 225°F, 10 to 30 min | Safe |
| Keystone Fryer & Grill Cleaner | 6018110032068 | 2 x 3.78 L | 1 to 2 quarts per fryer | Boil 15 min or soak 1 to 3 h | Do not use |
Directions from Keystone product pages and the Break-Up Professional spec sheet, checked November 19, 2026.
Why we lead with packets
Most fryer cleaning guides tell you to add a fryer cleaner and boil it. They skip the part where someone has to decide how much. In our experience the boil-outs that go wrong are the ones where someone guessed the dose or turned the heat up to finish faster. A pre-measured packet sized to your fryer, a set temperature range and three hot rinses fix most of that. Pick one product for the line, train to its label and stock it by the case.
Fryer and grill cleaning supplies

Item ID 6018113311337. 26 x 8 oz packets. Non-caustic, one packet per 50 lb fryer, safe for aluminum.

Item ID 7425145444466. 36 x 2 oz pouches. Low foaming, no neutralizing step, safe for aluminum.

Item ID 6018110032068. 2 x 3.78 L. Liquid for fryers, grills and ovens. Not for aluminum.

Item ID 6018101357354. 30 x 3.6 oz packets for flat tops cleaned while hot. No rinse needed.

Item ID 6018100330358. 6 x 20 oz aerosol for oven and grill grease. Corrosive, so wear gloves and goggles.

Item ID 6018102798712. 2 x 3.78 L pot and pan detergent for washing fryer baskets in the sink.
Browse all cleaners and degreasers or the full Keystone range. Building a schedule? Our Alberta kitchen cleaning schedule template has a spot for boil-outs. For case quotes on a whole fryer line, contact our Calgary team.
Frequently asked questions
How do you use Keystone Fryer Cleaner?
Turn the fryer off and drain the oil. Fill with cold water to cover the elements, below the fill line. Add one Keystone Fryer Cleaner packet, hold 180°F to 210°F for 15 to 20 minutes, then cool, scrub, drain and rinse with hot water at least three times. Dry fully before adding oil.
How many packets of fryer boil-out do I need?
Keystone Fryer Cleaner uses one 8 oz packet for a 50 lb fryer. Break-Up Professional uses one 2 oz pouch for a 15 to 20 lb fryer and two pouches for a 30 to 40 lb fryer. Keystone Fryer & Grill Cleaner takes 1 to 2 quarts. Fill the water first, then add the cleaner.
What temperature do you boil out a fryer at?
Keystone says 180°F to 210°F on the boil-out setting for its Fryer Cleaner. Break-Up says hold a gentle boil at about 225°F (105°C). Don't let it reach a rolling boil. A rapid boil can push hot solution over the top of the frypot and onto the floor.
How long do you boil out a commercial fryer?
Keystone Fryer Cleaner holds for 15 to 20 minutes, and Keystone's cleaning guide uses 20. Break-Up allows a gentle boil for 10 to 30 minutes. Keystone Fryer & Grill Cleaner boils for 15 minutes or soaks for 1 to 3 hours. Keystone puts the whole job at about 45 minutes.
Do you need vinegar after a fryer boil-out?
Not with Keystone Fryer Cleaner or Break-Up Professional. Keystone says no acidic rinse is needed and Break-Up says no neutralizing step is needed. Rinse with hot water at least three times instead. Vinegar rinses belong to older caustic products, so follow your own product's label.
How often should you boil out a fryer?
Keystone's guide says to clean the fryer when you change the oil, as needed. Kitchens that fry all day often boil out weekly, and lighter users go longer. Watch for dark carbon on the walls and elements, foaming oil or off flavours. Those mean it's overdue.
Can you boil out an aluminum fryer?
Yes, with the right product. Keystone lists its Fryer Cleaner as safe for aluminum fryers, and Break-Up Professional is listed safe for aluminum. Keystone Fryer & Grill Cleaner says do not use on aluminum, so keep that one for stainless fryers, grills and ovens.
Is Keystone Fryer Cleaner caustic?
No. Keystone describes it as a non-caustic boil-out that's easier on your fryer than caustic cleaners, and it needs no acid rinse. Keystone Fryer & Grill Cleaner is different. Its SDS lists 5 to 10% sodium hydroxide and the signal word Danger. Wear gloves, an apron and goggles for both.
What is the difference between Keystone Fryer Cleaner and Fryer & Grill Cleaner?
Keystone Fryer Cleaner is a non-caustic 8 oz packet made only for boil-outs and safe on aluminum. Keystone Fryer & Grill Cleaner is a 3.78 L liquid for fryers, flat tops, grills and ovens. It boils out at 1 to 2 quarts, isn't for aluminum and is corrosive per its SDS.
Why does my fryer boil over during a boil-out?
The usual causes are too much heat or too much water. Keystone says to avoid a rapid boil and to keep the water below the fill line. Break-Up says to control the temperature at about 225°F to prevent boil over. A low-foaming cleaner like Break-Up also helps.
Can you use dish soap to boil out a fryer?
Dish soap isn't sold as a fryer boil-out, and soap foams. Boil-out products like Break-Up are registered as carbon removers for cooking equipment and are made to be low foaming. Use dish soap where it belongs, on baskets in the sink with a pot and pan detergent.
How do you calculate shipping on bulk orders?
We calculate shipping on live carrier rates at checkout, not on flat or subsidized tiers. Every order is priced against real LTL, parcel, or pallet-freight quotes from our Calgary warehouse to your dock. That means you never absorb hidden shipping costs into product margins - what we charge is what the carrier charges us, plus a small handling pass-through. For bulk and pallet orders this typically runs 15–25% lower than competitors who bake shipping into their unit prices, because the rate is transparent and tied to the actual shipment weight and distance.
Sources we checked
- Keystone, Fryer Cleaner product page and directions
- Keystone, cleaning procedures guide
- Keystone, Fryer & Grill Cleaner product page
- Safety Data Sheet referenced for Keystone Fryer & Grill Cleaner
- Keystone, High Temp Grill Cleaner product page
- Diversey, Break-Up Professional fryer boil-out spec sheet
- NSF, Break-Up Professional registration letter
- Reddit r/KitchenConfidential, vinegar for fryer boil-out
- Reddit r/KitchenConfidential, cleaning fryer thread
Why Partner With ChickenPieces
Restaurants, food trucks, concession stands and commissary kitchens buy fryer cleaners, degreasers and janitorial chemicals from us by the case. Chicken Pieces is a Calgary foodservice, hospitality and medical supply company founded in 2018, with about 20,000 products in the online catalogue. We supply pantry ingredients, medical nutrition and kitchen supplies. We are not a poultry or meat distributor.
Local Calgary Support
Real people in Calgary answer the phone and check labels, pack sizes and stock for you.
Wide Product Range
Pantry staples, medical nutrition, disposables, janitorial and concession supplies from one supplier.
No Membership Needed
Order by the case or the pallet with no membership and no minimum order quantity.
Food Safe Focus
We write for operators working under CFIA and Health Canada aware food safety plans.
Request Your Custom Quote Today
Call 1-833-462-8550 or shop chickenpieces.com. Browse Cleaners and Degreasers for the full range.
Request a Quote