Quat Sanitizer PPM for a 3-Compartment Sink: A Guide

2026 Jul 25th

Quat Sanitizer PPM for a 3-Compartment Sink: A Guide

Canadian-Owned No MOQ Ships Canada-Wide Calgary Warehouse Food Safe Focus
Kitchen sanitation
CP

Chicken Pieces Editorial

Chicken Pieces · Calgary, AB

Quat Sanitizer PPM for a 3-Compartment Sink: A Guide

The working PPM target for a quat sanitizer bay, and how to test it in a three-compartment sink.

Quick Answer

A no-rinse quat sanitizer bay in a three-compartment sink is normally run at about 200 ppm, the working target most food-contact quat labels are built around. Health guidance commonly accepts a 150 to 400 ppm band, depending on the product and local code. Test the bay with strips, and dose from the label, not from memory.

Sanitizer calculator

Quat dilution for a three-compartment sink

Enter the sanitize-bay volume, your target PPM, and the active quat percent from the product label. The result is the amount of concentrate to add to that bay.

Sanitize-bay volume
Use the water you actually put in the sanitize bay, not the rim-full stamp on the sink.
Default is 200 ppm, the usual food-contact working target. The accepted band is 150 to 400 ppm. Follow the product label and your local code if they set a different number.
Read the active ingredient percent from the jug. The 10% shown here is only a starting illustration so you can see a worked result. Replace it with the number on your own label. We do not pre-load a brand percentage, because SDS sheets often give a range, not the exact dose strength.

Enter a volume, a target PPM, and the label percent to see how much concentrate to add.

Three-compartment sink, with the sanitize basin highlighted Wash, rinse, and sanitize basins in a row. The right-hand sanitize basin is highlighted and labelled with the calculated dose. Wash Rinse Sanitize This bay SANITIZE BAY Volume: 20 L Target: 200 ppm Add 40 mL 1.35 US fl oz

Always confirm with a quat test strip and the product label. This calculator applies the dilution arithmetic only. The registered label on the jug in your hand is the legal instruction, and a test strip tells you what the bay is actually running.

How this is calculated

Parts per million is milligrams of active sanitizer per litre of finished solution. That is the same as the volume fraction of concentrate, multiplied by the active strength as a decimal, multiplied by 1,000,000.

Rearranged for a kitchen pour, and with volume entered in litres, the dose is:

mL of concentrate = (target PPM × litres of water) / (active percent × 10)

US gallons are converted first, using 1 US gallon = 3.785411784 litres. Fluid ounces are converted from millilitres using 1 US fl oz = 29.5735295625 mL.

Worked example. A 20 L sanitize bay, a 200 ppm target, and a 10% active concentrate:

mL = (200 × 20) / (10 × 10) = 4000 / 100 = 40 mL

40 mL is 1.35 US fl oz. To check the other direction: 40 mL of a 10% concentrate in 20 L (which is 20,000 mL) is (40 / 20,000) × 0.10 × 1,000,000 = 200 ppm.

The same 10% concentrate at 200 ppm is 2 mL per litre, which sits at the mild end of the 2 to 5 mL per litre band described in this guide. A 4% concentrate at 200 ppm would be 5 mL per litre. Your jug may differ, so use the percent on its label.

Overview

Start here

⚡ Quick Answer

A no-rinse quaternary (quat) sanitizer bay in a three-compartment sink is normally run at about 200 ppm, the working target most food-contact quat labels are built around (health guidance commonly accepts a 150 to 400 ppm band, depending on the product and local code). To hit roughly 200 ppm, most concentrates dose in the region of 2 to 5 mL per litre of water, about 0.25 to 0.7 US fl oz per gallon, but the registered label on the jug in your hand is the exact, legal instruction. ChickenPieces.com stocks quaternary and low-temp concentrates in litre formats and ships them from Calgary with no minimum order.

The details

What concentration does the sanitizer bay actually need?

Most guides hand you the wash to rinse to sanitize ritual and the compartment order, then skip the one number you need to buy the chemical: the target concentration. For a no-rinse quaternary sanitizer used on food-contact surfaces, that target is about 200 parts per million. Canadian and North American food-safety guidance typically accepts a band of roughly 150 to 400 ppm depending on the manufacturer's instructions and the local health code, with the sanitized surface kept visibly wet for the label's minimum contact time, commonly around one minute, before air drying.

Say this plainly: the registered label on the container in your hand is the instruction that counts. Chemistry and water hardness differ, and a label range exists because the manufacturer tested it. Use the figures here to check that your label reads like others in the category, then dose to your own label and verify.

Why this matters for inspection: a correct compartment order with an under-dosed sanitizer bay is still a failure. Inspectors check the concentration, not just the sequence.
The method

How many ounces of concentrate go into a gallon of water?

To reach roughly 200 ppm, most food-contact quat concentrates dose somewhere in the region of 0.25 to 0.7 US fluid ounces per US gallon, which is about 2 to 5 mL of concentrate per litre of water. The exact figure depends on the product's active strength, which is why two similar quat concentrates can call for slightly different pours to land on the same ppm.

Metric matters more than most operators expect, because these concentrates are sold in litre formats. One US gallon is 3.785 litres and one US fluid ounce is 29.57 millilitres, so 0.25 oz per gallon works out to about 1.95 mL per litre and 0.67 oz per gallon to about 5.2 mL per litre. Do the conversion once against your own label and tape it above the bay.

The method

How many sink fills does one case actually give you?

This is the number that turns a dilution rate into an order quantity, and it is pure arithmetic once you know your dose. Work an illustrative example. A two-unit case of 3.78 L concentrate holds 7.56 L, or 7,560 mL. Dose at the weak end of a typical band, roughly 2 mL per litre of water, and that case makes about 3,780 L of finished solution. A ten US gallon sink bay is 37.85 L, so the case covers close to 99 fills. Dose at the strong end, about 5.2 mL per litre, and the same case makes roughly 1,454 L, or about 38 fills.

That spread, a two-and-a-half-fold swing across one label's own range, is the argument for measuring rather than free-pouring. Run the same division against your product's stated dose to get your real number. Chemical yield is only half the picture for a manual warewash line; the detergent bay has its own cost behaviour, which we break down in our guide to manual dish detergent cost per sink turn.

Guide

Sanitizer concentrates at a glance

ProductTypeUnit sizeBest for
Clean Essential No-Rinse SanitizerQuaternary3.78 L ×2General sink and bucket duty
Avmor Sani Stuff ConcentrateQuaternary4 L ×2Single-chemistry sites
Clean Quick Quick Cleaner ConcentrateQuaternary3.78 L ×3Higher-turn kitchens
Diversey Food Surf D10Quat sanitizer-detergent2.5 L ×2One-step food-contact surfaces
SUMA Low Temp T20Low-temp machine sanitizer3.78 L ×4Low-temperature dish machines
Ecolab 147 Multi DispenserQuaternary, dispenser-fed9.5 L ×1Wall-dispenser programmes
Diversey Chlorine Test StripVerification (chlorine only)1 unitChlorine bays, not quat

Formats reflect current catalogue listings. This is a format and chemistry comparison, not a price list, live pricing is shown on each product page and shipping is quoted on real carrier rates at checkout.

The details

Why a sani bucket stretches a case further

Working kitchens raise this point often, and the arithmetic backs it up: a wiping bucket holds a few litres where a three-compartment sink bay holds tens of litres, so at the same concentration a bucket change consumes a small fraction of the concentrate a full fill does. Crews that run disciplined bucket changes and fill the bay only for real warewash cycles go through cases far more slowly.

Septic sites: quaternary ammonium compounds are antimicrobial by design, so over-strength discharge is the live concern for a private septic system. Dose to label rather than by eye, and check the product label plus your local wastewater rules before standardising a septic site on quat.
The details

Test strips: what to verify with

The correct practice for a quat bay is to verify concentration with quat-specific test strips at every fill and log the reading. We will give you that advice and then tell you straight: our test-strip listing is the Diversey Chlorine Test Strip, which reads chlorine. A chlorine strip will not give a valid quat reading, and using one on a quat bay produces a number that looks like verification and is not. If your operation runs chlorine sanitizer, that listing is the right product. If you run quat, buy quat strips from your chemical representative or a lab supplier, and keep them in a dry drawer rather than the splash zone where humidity degrades them.

The details

What gets an operator written up at the sink?

Four recurring mistakes come up again and again. Washing produce in the sanitizer bay: a no-rinse quat is labelled for food-contact surfaces, not for produce, which belongs in a designated prep sink with a product labelled for that job. Thawing or storing product in the sanitizer bay: that bay has one function, and using it for anything else breaks the compartment logic and invites a citation. Treating a hand-dip as a substitute for handwashing after raw-protein prep: a dip supplements a proper handwash at a dedicated sink, it never replaces it. And running the bay off-label on temperature: follow the minimum temperature on the label, because efficacy claims are tied to the tested conditions.

US operators map these back to the FDA Food Code and the EPA registration on the label. Canadian operators work to their provincial food-premises regulation with the product's Health Canada registration, so confirm the product is registered for food-contact sanitizing before you standardise on it.

The method

How it works in Canada

Buying from a Canadian distributor keeps the supply chain short and the paperwork simple. ChickenPieces.com stocks quaternary sink concentrates, low-temp machine sanitizers and dispenser-fed units, and ships them Canada-wide from our Calgary warehouse with no minimum order, so you can trial a single case before committing a group of sites, and reorder against real usage. Shipping is quoted on live carrier rates at checkout rather than baked into unit prices.

Clean Essential Disinfectant No Rinse Sanitizer, Quaternary
Clean Essential No-Rinse Sanitizer, Quaternary
3.78 L × 2 per case · sink and bucket duty
View product →
Avmor Quaternary Sanitizer, Sani Stuff Concentrate
Avmor Sani Stuff Quaternary Concentrate
4 L × 2 per case · single-chemistry sites
View product →
Diversey Chlorine Test Strip
Diversey Chlorine Test Strip
Chlorine bays only, not valid for quat
View product →
The details

What Canadian operators say

★★★★★

"ChickenPieces shipped to our Calgary cafe inside 48 hours, pricing beat our previous supplier on the bulk shortening line. Already reordered."

CP Buying Desk, Alberta · Alberta (Calgary)

★★★★★

"Switched our Mississauga commissary to CP for syrups and cleaners. Spec sheets arrive with the order, no chasing. Solid for GTA foodservice."

Giselle R., Ontario · Ontario (Toronto)

★★★★★

"Vancouver hotel pantry switched to CP bubble-tea and concession supplies. No membership, transparent pricing, Canada-wide delivery worked for us."

Front-of-house buyer, BC · British Columbia (Vancouver)

Field tip

Trust the strip, not the last pour

Field tip: Test strips tell you what the sink is actually running, not what the bottle should have made. If the reading is off, dump the bay and remix from the label dose.
Shop the Range

Quat and chlorine sanitizers

Diversey Suma Quat Sanitizer 3.78 L/1 Gallon (4/Case)
Diversey Suma Quat Sanitizer 3.78 L/1 Gallon (4/Case)

Item ID 7425132987945. Quat sanitizer, 3.78 L jug, 4 per case.

Avmor Quarternary Sanitizers, Sani Stuff Concentrate | 4L/Unit, 2 Units/Case
Avmor Quarternary Sanitizers, Sani Stuff Concentrate | 4L/Unit, 2 Units/Case

Item ID 6010854889878. Quat sanitizer concentrate, 4 L jugs, 2 per case.

Diversey Suma® Detergent Sanitizer, Concentrate Closed Loop 3.78 L/1 Gallon (4/Case)
Diversey Suma® Detergent Sanitizer, Concentrate Closed Loop 3.78 L/1 Gallon (4/Case)

Item ID 7425142115109. Detergent sanitizer concentrate, 3.78 L closed loop.

Luster Professional Liquid Chlorine Sanitizer, Concentrate, 3.78 L/1 Gallon (2/Case)
Luster Professional Liquid Chlorine Sanitizer, Concentrate, 3.78 L/1 Gallon (2/Case)

Item ID 7425129214245. Liquid chlorine sanitizer concentrate, 3.78 L.

Diversey Chlorine Test Strip | 1UN/Unit, 1 Unit/Case
Diversey Chlorine Test Strip | 1UN/Unit, 1 Unit/Case

Item ID 6010856697648. Chlorine test strips for sink and bucket checks.

Cases ship to Canada and the US at live UPS rates. Pallets and frozen products ship within Canada only. Free shipping over $199 CAD is Canada only.

FAQ

Frequently asked questions

What is the required PPM for quat sanitizer?

A no-rinse quat sanitizer bay in a three-compartment sink is normally run at about 200 ppm, the working target most food-contact quat labels are built around. Health guidance commonly accepts a 150 to 400 ppm band, depending on the product and local code. Always follow the label and your inspector’s requirement. See this quat PPM guide.

What PPM does quat sanitizer need to be?

For food-contact quat in a three-compartment sink, 200 ppm is the usual target. Single-quat solutions are often aimed at 200 ppm, and some multi-quat labels use a 200 to 400 ppm range. Local health codes and the product label decide the exact band, commonly around 150 to 400 ppm. Test the sink with the right quat test strips, not a guess.

How do you test quat sanitizer concentration?

Use quat test strips made for that sanitizer, dip them in the sink, and read the PPM against the chart. Retest during the shift, because food soil can bind quat and drop the reading. If it falls below about 200 ppm, change the solution. Follow the strip and the label, not a spoon measure.

What sanitizer is used in a 3-compartment sink?

The third bay is typically a no-rinse quat sanitizer mixed to the label’s food-contact PPM, usually about 200 ppm. A 3.78 L no-rinse quat and other labelled concentrates are used for that bay. Wash and rinse still come first. Confirm the mix with quat test strips during the shift.

What happens if quat sanitizer PPM is too high?

If the solution is stronger than the label and local code allow, it can leave residue, irritate skin, and fail an inspection just as a weak solution can. The usual food-contact target is about 200 ppm, with a broader 150 to 400 ppm band on some labels. Dump an over-strong sink, remake it, and test again before dishes go in.

What is the difference between quat and chlorine sanitizer?

Quat and chlorine are different chemistries, with different test strips, mix rates and limits. This guide describes a no-rinse quat sink at about 200 ppm. Do not use chlorine strips on a quat sink, and do not copy a chlorine recipe onto a quat label. Read the SDS and the bottle in front of you.

Is quat sanitizer safe for food-contact surfaces?

Yes, when you use a product labelled for food-contact surfaces and mix it to the stated PPM, usually about 200 ppm in a no-rinse three-compartment sink. No-rinse quat concentrates are made for that job. Follow the label, local code, and your SDS. Rinse is not a substitute for the correct concentration.

How often should you change quat sanitizer solution?

Change the sink when test strips show the PPM has dropped, when the water is dirty, or when your health department’s schedule says to. Food soil can bind quat and pull the reading below about 200 ppm. Remake the solution and test it before the next rack. Keep a written log if your inspector requires one.

What is quat binding?

Quat binding happens when food soil, grease or some cloths tie up quat molecules so the solution tests weaker than when you mixed it. The sink can look fine and still sit below about 200 ppm. Retest during the shift and change the solution when the reading drops. Clean first, then sanitize.

How much quat do you add per litre of water?

There is no single household spoon measure that works for every quat. Concentrates differ, so the only safe method is the dilution on that product’s label, mixed to the food-contact target, usually about 200 ppm, and checked with quat test strips. Ignore generic “tablespoon per litre” advice. If the reading is off, remake the sink from the label.

Why Partner With ChickenPieces

Chicken Pieces is a Calgary foodservice, hospitality and medical supply company founded in 2018, with about 20,000 products in the online catalogue. We supply pantry ingredients, medical nutrition and kitchen supplies. We are not a poultry or meat distributor.

Local Calgary Support

Real people in Calgary answer the phone and check labels, pack sizes and stock for you.

Wide Product Range

Pantry staples, medical nutrition, disposables, janitorial and concession supplies from one supplier.

No Membership Needed

Order by the case or the pallet with no membership and no minimum order quantity.

Food Safe Focus

We write for operators working under CFIA and Health Canada aware food safety plans.

Request Your Custom Quote Today

Call 1-833-462-8550 or shop chickenpieces.com. Browse Kitchen supplies for the full range.

Request a Quote